You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
85 lines
3.7 KiB
C
85 lines
3.7 KiB
C
// USER DEFINED SETTINGS V16
|
|
// Set fonts to be loaded, pins used and SPI control method
|
|
|
|
|
|
// ##################################################################################
|
|
//
|
|
// Define the fonts that are to be used here
|
|
//
|
|
// ##################################################################################
|
|
|
|
// Comment out the #defines below with // to stop that font being loaded
|
|
// As supplied font 8 is disabled by commenting out
|
|
//
|
|
// If all fonts are loaded the extra FLASH space required is about 17000 bytes...
|
|
// To save FLASH space only enable the fonts you need!
|
|
|
|
#define LOAD_GLCD // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
|
|
#define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
|
|
#define LOAD_FONT4 // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
|
|
#define LOAD_FONT6 // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
|
|
#define LOAD_FONT7 // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:.
|
|
//#define LOAD_FONT8 // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
|
|
|
|
|
|
// ##################################################################################
|
|
//
|
|
// Define the pins that are used to interface with the display here
|
|
//
|
|
// ##################################################################################
|
|
|
|
// We must use hardware SPI
|
|
// FYI Mega SCK is pin 52, MOSI is 51, UNO/NanoPro micro etc SCK is pin 13 and MOSI is 11
|
|
// Leonardo Pro micro SCK is pin 15 and MOSI is 16
|
|
|
|
// These are the control pins I use on my Mega setup
|
|
// TFT_CS 47 // Chip select control pin
|
|
// TFT_DC 48 // Data Command control pin
|
|
// TFT_RST 44 // Reset pin (could connect to Arduino RESET pin)
|
|
|
|
// These are the control pins I use on my UNO/Nano/Pro Micro/ATmega328 setup
|
|
// TFT_CS 10 // Chip select control pin
|
|
// TFT_DC 9 // Data Command control pin
|
|
// TFT_RST 7 // Reset pin (could connect to Arduino RESET pin)
|
|
|
|
// ###### EDIT THE PIN NUMBERS IN THE 3 LINES FOLLOWING TO SUIT YOUR SETUP ######
|
|
|
|
#define TFT_CS 49 // Chip select control pin
|
|
#define TFT_DC 48 // Data Command control pin
|
|
#define TFT_RST 8 // Reset pin (could connect to Arduino RESET pin)
|
|
|
|
|
|
// ##################################################################################
|
|
//
|
|
// Other speed up options
|
|
//
|
|
// ##################################################################################
|
|
|
|
// If your sketch uses the GLCD font in size 1 with background then uncomment
|
|
// this next line will speed up rendering x5, code size will increase 136 bytes
|
|
// Only worth it if you print lots of GLCD font text...
|
|
|
|
#define FAST_GLCD
|
|
|
|
// Uncomment the following #define to invoke a 20% faster drawLine() function
|
|
// This speeds up other funtions such as triangle outline drawing too
|
|
// Code size penalty is about 72 bytes
|
|
|
|
#define FAST_LINE
|
|
|
|
// Comment out the following #define to stop boundary checking and clipping
|
|
// for fillRectangle()and fastH/V lines. This speeds up other funtions such as text
|
|
// rendering where size>1. Sketch then must not draw graphics/text outside screen
|
|
// boundary. Code saving for no bounds check (i.e. commented out) is 316 bytes
|
|
|
|
//#define CLIP_CHECK
|
|
|
|
// Comment out the following #define if "SPI Transactions" do not need to be
|
|
// supported. Tranaction support is required if other SPI devices use interrupts.
|
|
// When commented out the code size will be ~700 bytes smaller and sketches will
|
|
// run slightly faster, so leave it commented out unless you need it!
|
|
// Transaction support is needed to work with SD libraru but not needed with TFT_SdFat
|
|
|
|
#define SUPPORT_TRANSACTIONS
|
|
|